MikroTik/RouterBOARD cAP ac
    • MikroTik/RouterBOARD cAP ac
    • MikroTik/RouterBOARD cAP ac
    • MikroTik/RouterBOARD cAP ac
    • MikroTik/RouterBOARD cAP ac

    cAP ac

    588,00 kr
    Exkl. moms 1-3

    Dual-band 2.4 / 5GHz wireless access point for mounting on a ceiling or wall with two Gigabit Ethernet ports (one with PoE output) and 802.11ac support

    Mängdrabatter

    KvantitetRabattDu Sparar
    205%Upp till 588,00 kr
    Kvantitet
    I Lager

     

    Order vardag före 12.00 går normalt samma dag med Postnord. Fri frakt över 4000kr

     

    All retur ska godkännas av oss sänd mail till info@shlab.se

    The cAP ac is a very capable and powerful wireless access point that looks beautiful on both walls and ceilings. The concurrent dual band wireless radio supports dual chain 2 GHz and 5 GHz in 802.11ac and legacy standards, and will provide coverage in 360 degrees around it.

    Even though the radio supports repeater mode, the two Ethernet ports give you the ability to extend your network with cables, even if PoE power is required, since the cAP ac supports 802.3af/at PoE input on the first port, and passive PoE output on the second port.

    - cAP ac (International) supports 2412-2484MHz and 5150MHz-5875MHz range (Specific frequency range can be limited by country regulations).

    Specifications

    Details
    Product codeRBcAPGi-5acD2nD
    ArchitectureARM 32bit
    CPUIPQ-4018
    CPU core count4
    CPU nominal frequency716 MHz
    DimensionsRound case: ⌀ 136 mm, height: 30 mm; Square case: 145 mm x 145 mm x 30 mm
    License level4
    Operating SystemRouterOS
    Size of RAM128 MB
    Storage size16 MB
    Storage typeFLASH
    Tested ambient temperature-40 to 50° C

    Powering

    Details
    Max Power consumption13W
    PoE in802.3af/at
    PoE outPassive PoE up to 57V
    PoE in input Voltage17-57 V
    Number of DC inputs1 (PoE-IN)

    Wireless

    Details
    Wireless 2.4 GHz number of chains2
    Wireless 2.4 GHz standards802.11b/g/n
    Antenna gain dBi for 2.4 GHz2
    Wireless 2.4 GHz chip modelIPQ-4018
    Wireless 5 GHz number of chains2
    Wireless 5 GHz standards802.11ac
    Antenna gain dBi for 5 GHz2.5
    Wireless 5 GHz chip modelIPQ-4018

    Ethernet

    Details
    10/100/1000 Ethernet ports2

    Wireless specifications

    2.4 GHzTransmit (dBm)Receive Sensitivity
    1MBit/s26-100
    11MBit/s26-94
    6MBit/s26-96
    54MBit/s23-78
    MCS026-96
    MCS722-73
    5 GHzTransmit (dBm)Receive Sensitivity
    6MBit/s26-96
    54MBit/s21-80
    MCS026-96
    MCS720-75
    MCS918-70

    Ethernet test results

    RBcAPGi-5acD2nDIPQ-4018 1G all port test
    ModeConfiguration1518 byte512 byte64 byte
    kppsMbpskppsMbpskppsMbps
    Bridgingnone (fast path)162.51973.4469.91924.71484.8760.2
    Bridging25 bridge filter rules162.11968.5352.91445.5359.2183.9
    Routingnone (fast path)162.51973.4469.91924.71488761.9
    Routing25 simple queues162.51973.4469.91924.7506.3259.2
    Routing25 ip filter rules162.21969.8240.8986.3242.9124.4
    1. All tests are done with Xena Networks specialized test equipment (XenaBay),and done according to RFC2544 (Xena2544)
    2. Max throughput is determined with 30+ second attempts with 0,1% packet loss tolerance in 64, 512, 1518 byte packet sizes
    3. Values in Italic indicate that max throughput was reached without maxing out CPU, but because board interface configuration was maxed out
    4. Test results show device maximum performance, and are reached using mentioned hardware and software configuration, different configurations most likely will result in lower results

    IPsec test results

    RBcAPGi-5acD2nDIPQ-4018 IPsec throughput
    ModeConfiguration1400 byte512 byte64 byte
    kppsMbpskppsMbpskppsMbps
    Single tunnelAES-128-CBC + SHA137.9424.559241.761.631.5
    256 tunnelsAES-128-CBC + SHA136403.238.5157.739.820.4
    256 tunnelsAES-128-CBC + SHA25636403.238.5157.739.820.4
    256 tunnelsAES-256-CBC + SHA134.4385.337.9155.239.820.4
    256 tunnelsAES-256-CBC + SHA25634.4385.337.9155.239.820.4
    1. All tests are done with Xena Networks specialized test equipment (XenaBay),and done according to RFC2544 (Xena2544)
    2. Max throughput is determined with 30+ second attempts with 0,1% packet loss tolerance in 64, 512, 1400 byte packet sizes
    3. Test results show device maximum performance, and are reached using mentioned hardware and software configuration, different configurations most likely will result in lower results

    Included parts

    MikroTik
    m RBcAPGi-5acD2nD
    32 objekt
    2020-01-24